Auq 180 remap

[Liam180cupra]

I had a remap recently and I'm not sure if my torque figures are as good as they should be.
I'm running 211bhp 220lb/ft torque. 21psi boost
Stage 1
Mods:
Forge dv 008
Decat
N249 bypass
4 bar fpr
Aluminium smic
Race tube exhaust
Cone filter
Silicon boost pipes

 

[tom w]

generic stage1 map ?
What were you expecting ??
As ko3s turbo engines top out 240-245bhp - 280-300ftlbs on a custom stage 2 map

 

[Liam180cupra]

no it was a custom map on a rolling road.
I was thinking around 235ish (torque)
I have done a few bits since the remap.
decat and 4 bar fpr.
Would i be able to get a abit more power by getting it back on the dyno as im not bothered about stage two.

 

[D_hatfield]

generic stage1 map ?
What were you expecting ??
As ko3s turbo engines top out 240-245bhp - 280-300ftlbs on a custom stage 2 map

Can you just swap the turbo from the cupra r. Onto the AUQ ?


Sent from my iPhone using Tapatalk

 

[tom w]

With manifold , oil feed pipe ,tip injectors etc.. it's fairly easy

 

[tom w]

no it was a custom map on a rolling road.
I was thinking around 235ish (torque)
I have done a few bits since the remap.
decat and 4 bar fpr.
Would i be able to get a abit more power by getting it back on the dyno as im not bothered about stage two.

Why 4 bar fpr ??
It will cause over fuelling if not mapped in for it not many mappers need them anymore
You're nearly ready for stage 2 why don't you want to go for it ??

 

[D_hatfield]

Is it the ko4s turbo on the bam ,? What figured could u expect when u put the ko4s on a AUQ with remaps etc ..?


Sent from my iPhone using Tapatalk

 

[tom w]

Yes bam and amk codes
You'll see the same results as the Cupra R /TT
Max out @ 280bhp /300ftlbs

 

[D_hatfield]

Yes bam and amk codes
You'll see the same results as the Cupra R /TT
Max out @ 280bhp /300ftlbs

May take that route then ! Get the bigger turbo


Sent from my iPhone using Tapatalk

 

[tom w]

You can get all the parts in a kit
Turbo ,manifold ,oil lines , tip, maf, fuel pump , downpipe , injectors

Or depends on what mods you have ( uprated exhaust etc...) hybrid gives bigger numbers and a like for like fitting

 

[D_hatfield]

You can get all the parts in a kit
Turbo ,manifold ,oil lines , tip, maf, fuel pump , downpipe , injectors

Or depends on what mods you have ( uprated exhaust etc...) hybrid gives bigger numbers and a like for like fitting

So how much are we like looking at for a kit ,? I only have a cone filter on at the moment , I have an exhaust that ain't fitted tho !


Sent from my iPhone using Tapatalk

 

[tom w]

I've seen them on Facebook for £300 for used kits minus fuel pumps and down pipes

 

[D_hatfield]

I've seen them on Facebook for £300 for used kits minus fuel pumps and down pipes

Must stop wasting my money on the weekends and start putting it into my car !


Sent from my iPhone using Tapatalk

 

[Liam180cupra]

Wouldn't it be easier to hybrid the original ko3s turbo?
What else do I need for stage 2?
It's not over fueling with the 4bar fpr