Search results

I have to say I was shocked when they said that anyone can buy from them, no point in it being called trade if that's the case

It's a total pain in the ass to get to but well worth a check, I spent months trying to trace the fault

Sounds like the N75, if its not working it wont be regulating the pressure to the actuator

TPS will also supply to the general public, bought all the stuff for my car from them. Also if the N75 doesnt work check the Y pipe under the inlet manifold, mine had a hairline split in it and was causing boost fluctuation

How did you do a smoke test? Think I need to try that! As for the forge I had it in bits and pressure tested it about a week ago. I am starting to wonder if it is a different map. Slightly annoying.

Scanned the car no problems, totally standard car with no added weight. He even runs his on supermarket 95Ron and I put in V Power. I've been through the engine changing worn pipes, checking pretty much everything. His boosts really hard and puts you in the seat, mine is fairly quick but...

I've searched and never really come up with some straight answers so I'm just going to ask! Myself and a friend both have 2004 Leon Cupra R's with BAM engines. His was totally standard until he got a stage 1 map, I then decided to get exactly the same map. After the mapping I felt it was a...

Sorted my car now and i can keep it low with no issues other than lots of scrubbing. But if it aint scrubbing it aint low enough :p Keep the pics coming they look ace, will take some of mine too

Yo Dallan is that the grill fitted then? Looks spot on!!!

Anyone have to remove the rubber balance weight on the drivers driveshaft? Mine was battering the chassi leg. Im on 17s and they are all tucked in the arches, but now over 40mph it whines like a bitch and an expert said its because the shafts are running parallel so now the pressure on the...

If possible can you post a pic of your slammed cupra so i can compare and then i want to know who had or has issues now that only happened after it was lowered. Im trying to eliminate all possible causes of my driveshaft problems and need to know if im getting duff advice. Cheers

How did u move it over, they are rubber bonded to the shaft?

Snip snip, saw and sweat i did. Those things are bloody tough. Removed it and it steers like a dream, but now from 40ish mph to whatever its noisy as anything. Sounds like a mega loud knackered wheel bearing, but it never did it before. Could this be caused from removing it? Anyone else...

How the hell do some of the ibiza's run slammed on the deck. My balance weight on the drivers drive shaft if hitting the chassi leg thus not letting me steer correctly. Mine is not even low compared to some? Any ideas?

The coolant was changed before i got it so it seemed a waste to change it again. Thanks for the help, i shall just keep topping it up. Suppose there is nothing wrong as the temp never goes above 90 and the oil is mint.

Changed the water pump, quite a bit of fluid was lost. Topped up the expansion tank and let it warm up. Coolant was circultating fine. Next day when it was cold topped up to the line again. Do you need to bleed the system on the 20vt or are they self bleeding? Surely if it is circulating...

Its a bit of a crap guide as i had already fitted it when i realised i should have documented it. All i really need to do is tell u how to do it and u can work the rest out. Remove the plastic trunking that the ash tray and gear stick are surrounded by to allow more access. Remove the...

I should have taken pics but once i started i wanted it finished. The finished result is so much better than expected, much tighter and solid gear change. Doing the TT conversion soon to make it that bit better. I will take some pictures and show you how its done without jacking up the car...

Got the B&M short shifter copy from ebay, instructions said you need to remove the exhaust, heat shield and tray sealing the linkages from the outside. Everyone i asked did this but i couldnt be arsed fannying about under the car. With a little bit of skill i had it done in 1hr all from...