Search results

Some leave the sai pipe with no filter and report no problems. All mine has, is a little pcv filter from a ford focus in the end, (small foam block, squeezed to fit) and a cable tie to keep it out the way! Or you can bypass it, but mines awkward and doesn't agree with resistors! I do advise on...

A above+ a decent Turbo inlet pipe (tip) Prone to collapsing on the 210's and 225's and they restrict air flow... Mines only a 180 (standard) And I fitted an open cone filter, (£20) Forge split recirc. Valve (£150) (some advise against these) N249 bypass, (about a fiver for the vacuum hose) An...

Hello, Fault codes would be a big help, as the others have said, and; do you know if the wiring has been checked an the plug for the lambda sensor (s) And as someone else also said- are they fitting Bosch sensors? Vag vehicles DON'T like cheap and cheerful ones, they would probably tolerate...

Hello, Fault codes would be a big help, as the others have said, and; do you know if the wiring has been checked an the plug for the lambda sensor (s) And as someone else also said- are they fitting Bosch sensors? Vag vehicles DON'T like cheap and cheerful ones, they would probably tolerate...

Mine wasn't too bad to do, but then, I did away with all the original pipework for n249 and n112 valves, then re fitted the n112 differently, so I could stop the engine light from having a tantrum every couple of days... Made in Spain, made better in England;) 223.3hp 263.8lbft

Washed it Demon shined it Backed in to a post with it Oh yay :@ Made in Spain, made better in England;) 223.3hp 263.8lbft

These are the part numbers for the two 8mm (ish) vac/breather hoses kinda central on the lower side of the inlet mani: (AUQ) Sa06a103221B £15.02+ The longer one (breather) And S06a133783as £3.50+ The longer one (90degrees I think) That's the two that I believe are common, and I fitted them...

Assuming its the one I replaced, (or one of two) I can get the part numbers from work, as that's where I keep all my invoices, if I find the number for the two I fitted tomorrow, you could always get a picture of them from the part no, and compare to yours? I'm 99% sure it's one of the ones I...

Fitted #2 'welcome light', reset gear cables. Made in Spain, made better in England;) 223.3hp 263.8lbft

I might guess you have a 1.9tdi with that mpg, in which case, maybe the egr valve has seized up... Is it smoking/more than normal? Made in Spain, made better in England;) 223.3hp 263.8lbft

Haha, that can't be an AUQ then?! What engine you running ?? Mine is too embarrassing to put in my sig with power + torque lol (20-25 mpg avg, 27 on a 200 mile run!) Made in Spain, made better in England;) 223.3hp 263.8lbft

Did it help at all? Made in Spain, made better in England;) 223.3hp 263.8lbft

Bosch are pretty good, but occasionally they fail. I heard from an auto electrician today that Mercedes maf meters (perhaps irrelevant) have a life expectancy of 3 months or less INLESS genuine parts (NOT even Bosch) though I haven't had this issue before myself tho. Made in Spain, made...

Cheers:) As lee said, ebay, item no: 400448581299 I had a few issues with fitting, they kept going out, but I just assume they switch off them selves/time-out, which is fine with me, I don't normally take more than a five minutes to get in and out lol. Under £15 too... Made in Spain, made...

No probs mate, let us know tomorrow of you have any joy:) What make is your current maf meter? Made in Spain, made better in England;) 223.3hp 263.8lbft

Maybe a local Tps? MIGHT be cheaper than dealer,I'm normally pleasantly surprised by them (tonbridge Tps).(perhaps cause I'm in the trade?) Made in Spain, made better in England;) 223.3hp 263.8lbft

Can find part number if you still need it, changed mine last month, it's £18+the dreaded the other one is under a tenner (next to it) I did both, supplied by Tunbridge TPS You'll want some jubilees too, as the clips don't like being removed and re-fitted! Reece Made in Spain, made better in...

On the auq, if you look at the front if the engine bay, it's on the right side o the head, with two medium size flexible plastic (NOT rubber or silicon) pipes going to it, this for sai aswell. Coils normally are worse under load than at tickover, the first symptoms sound like maf. Do you have...

Sounds odd, is it runnin smoothly, or juddering? Have you got access to vag com/ a scanner/ fault code reader? Made in Spain, made better in England;) 223.3hp 263.8lbft

Fair enough, I've always changed mine more as precautionary measure also... And it's a good way to see if there any filings floating around. "Seat welcome light" Made in Spain, made better in England;) 223.3hp 263.8lbft