Search results

So I found a decent SEAT Leon mk2 1.6i 8v 102hp '06 with 155k km on it which I'm about to look and most likely to buy on the spot (fingers crossed), but I have some concerns since I'm the owner of a simple 1.4 16v 75hp SEAT Leon and I want to ask your honest opinion about: * Engine Is 1.6i 8v...

Hi, I'm trying to enable a hill hold control on my dad's car and I can't apply any coding to the ABS module on the VCDS: Address 03: ABS Brakes Labels: 1K0-907-379-MK60-F.lbl Part No SW: 1K0 907 379 AC HW: 1K0 907 379 AC Component: ESP FRONT MK60 0101 Revision: 00H11001...

In case someone has the same errors or your climatronic suddenly stops working and then after sometime starts working again I solved all of these issues by changing the blower motor. I learned it the hard way when the blower motor had died on me during winter so I had to fix it urgently no...

Figured out that the fuel pump was faulty. First I checked whether the relay was working when I turned the ignition on, it was easy to verify as it was within the reach and I just had to hear and touch it as it should produce a "click" when the ignition is on. Then I substitued the fuse #14...

Does anybody know the exact location of the fuel pump relay and what is its number? I suspect this is the problem.

My petrol Seat Cordoba (6L2, 1.4 BBZ) won't start and I noticed that when ignition is on there is no fuel pump sound in the car. After switching ignition off and on various times it still doesn't make any sound. Prior to this problem the car worked perfectly, no hick ups on starts nor on the...

You must have installed the steel wire to the lock's hook incorrectly, I've been through that, see my guide imgur.com/a/lQPg2. In your current situation you should unmount the door panel from the inside, it will be hard, but doable.

Hi everybody! Can anybody provide me with the ETKA schema of the installation of the noise insulation part 6Q0825237R? My car is petrol Seat Cordoba 6L2 2003 and the schema I need should be similar to this: realoem.me/Volkswagen/MEX/POVE/2013/677/R/8/825/825000 I assume I've installed it...

I have a few errors related to climatronic: 00710 (2C6) — Defroster Flap Positioning Motor (V107) 01274 (4FA) — Air Flow Flap Positioning Motor (V71) 01271 (4F7) — Positioning Motor for Temperature Flap (V68) 01272 (4F8) — Positioning Motor for Central Flap (V70) 01273 (4F9) — Fresh Air...

I drive 2003 version. It's a stock 1.4 sport version, tuning is prohibited in Portugal. Here is the pic made on her 10th birthday in Potes, Spain: i.imgur.com/3jvAu6W.jpg

I own one in English and can make photos if you still need them and it is not beyond the rules of the forum. Samples: i.imgur.com/INeiB6t.jpg i.imgur.com/4cfkMic.jpg

I doubt there is an easy option for you. I would connect a dashcam to the cigarette lighter, in your case it is #49 and install a hard wire kit with low voltage cut off (battery discharge prevention). This is the set up I use on my Cordoba 2003.

Once I was able to disassemble the whole rear right door on my Cordoba 2003 and it took me a while to understand what was going on there. Since your door is locked and you didn't detach the metal wall I recommend you to take out the metal wall and try to pull the steel wire again or to open the...

Thanks for the adaptation hint, from time to time I have acceleration issues and the engine even cuts out. Regarding the EGR - P0402, perhaps the valve is clogged with coal and cannot move properly, so you have to dismount EGR valve and clean it from the inside with some kerosene or similar...

Thanks a lot for your help. I managed to find it and also I got it fixed. The tube of the MAP sensor was dirty inside (looked like a dust and oil substance), I cleaned it with WD-40 and went for a ride. The car was immaculate (and it still is!), very responsive accelerator pedal, engine ran...

Hello. I have Seat Cordoba 6L2 (year 2003, 1.4l, 74kW/100bhp, engine type BBZ). Never had major problems with it, just did regular inspections, changed oil and bulbs. However for the last 7 moths I've been receiving from time to time error code P0106 - MAP/Barometric Pressure Circuit...