bottom

  1. RS6

    My Seat Leon Cupra R ** CAR SOLD* NEW CAR!

    Standard with Stage 2 mods fitted it made 235bhp and 219.4lb ft so not bad for a 210! AMD Stage 2 remap it made 270bhp + 319.4lb/ft with Forge TIP ------- Now Running Revo Stage 2 + Badger 5 TIP, Jetex Cone & Jabbasport Heat shield with cold air feed, X4 new coil packs, new thermostat...
  2. BXE head fit an ASZ bottom end? Anyone know?

    I've heard it's the new code for the older BKC engine but i'm only interested in the cylinder head and if it'll fit onto an ASZ lump, obviously after changing the injectors over. I know the BKC will fit but i'm not sure if the BXE head is exactly the same as it's a newer code and might have...
  3. Bottom Engine Cover screws question

    I had a quick look under my car yesterday night and noticed that the plastic underside engine cover at teh front of the car wasn't fully attached. Seems to be missing some screws. Was a bit dark to get under there and mess around so just wondering if people here know exactly which screws are...
  4. Ethan040

    Bottom section of front bumper

    Hi, im getting my bumpers colour coded and i want to cut the sections out of the front bumper like ive seen a few poeple do to there 1.4s i was just wondering whats the best way to do this? does it look a mess? would it have to be filled? how much is it to just buy the cupra section and doe sit...
  5. BBoy82

    Integrated Engineering 2ltr bottom end conversion...

    Hi all. Ive done a search, looking for information regarding the above, but cant seem to find anything... Basically, has anyone had it done, and if so, how much/who by? Im considering doing a home rebuild, so if anyone has any experience of this (what its like once completed, as opposed...
  6. rsmith

    LCR W.I.P Update K04 Hybrid- F23 Here, mini review page 50

    Hi all, I have been doing a lot of work on my engine bay as of late, i have most of the mods done now apart from the final 2 engine bay mods which are a mirror polished inlet manifold and a CAI, but i think i am nearly there and can finally start on uprating the handling on the LCR, starting...
  7. Moffat

    What's this for in the bottom of the airbox?

    What's this for in the bottom of the airbox? This blank type of thing. Is it so Seat can use the same airbox in different models? The bit in the top left hand corner of the airbox.
  8. coxyboy

    do i need 'k03s' metal tip bottom with forge tip???

    hi people have taken my turbo off today and it is shagged beond belief! all the blades have been rubbing the inside of the casing and actually worn the blades aways also there is a stupid amount of play in out and left right and i blown the oil seals lol so i would say ive broken it completely...
  9. Uprated Bottom Engine Steady (Torque Mount)

    Hi I have been looking for an uprated bottom engine steady/gearbox steady mount as my engine seems to have alot of play in it. I could just replace with a standard mount as mine looks a bit worn but was wondering if there are any other options out there. I found that Vibra Technics do one but...
  10. james walker

    suspension strut bottom bolt part number

    hi guys, anyone know the part number for the bolt that goes through the wheel bearing housing to hold the bottom of the strut into it? bolt and nut numbers if anyone knows..... cheers guys
  11. p34ch3y

    advice on blocking the bit off at the bottom of the forge tip

    is it ok to block this off also could i then block the bit off of the top of the throtle body and where it gos to the carbon filter thing block that there as well?
  12. 3 sensors on bottom end?

    Could easily be a stupid question but i couldnt find anything so ill have to come out with it, there is three sensors going into the bottom end. two about half way spaced equidistant and one near fly, possibly thinking its the crank position sender. The three sensors wires all meet at a...
  13. bottom arm/brake problem

    my auntie's says when she brakes in wet weather, the car feels like it doesn't want to stop as good as it should. I've checked her brakes, but they're fine. I did notice that there is alot of play in both the front wish bones. could this affect the braking at all? cheers
  14. GT28RS, Stock Bottom End & 1.3bar Boost.

    What's the general thoughts on running 1.3bar peak with a GT28RS and a stock bottom end?? It will hit 1.3bar at about 3500rpm and hold it to the rev limiter. Is this a safe level or a little too high?
  15. How to replace the bottom radiator hose?

    Hi everyone New to the site, only recenlty bought my Ibiza. Its been lowered and recently i went over speedbump which has resulted in a split in the bottom radiator hose. Just wondering what the best way is to replace this. Is it a case of having to remove the front bumper to get access to...
  16. 16v head, 8v bottom end

    I haven't done any research on this yet but had the idea last night, Are there any 16v heads that will fit with an 8v bottom end? My car is a 96 cordoba sx 1.6 8v. I know a 2 litre swap is easily done but i like the idea of a 1.6 16v, hopefully still keep my mpg above 40! Any help...
  17. Leon Cupra Bottom Ball Joint

    Can anyone tell me if a new bottom ball joint comes supplied with a bracket and 3 bolts? Reason for asking is that I've removed my suspension arms to get them rebushed (powerflex). I decide it was easiest to undo the 3 bolts on each arm that hold the balljoint, leaving the joint still...
  18. Did we ever get to the bottom of the Angel Eyes?

    Did we ever finish the debate about the Angel Eyes - the wicked german imported, LHD beam, black ones that we were debating about with RichT and Co. last month? Are they all the same pre/pst 96? can they be modded to RHD beam pattern? how? Will they pass an MOT with a wink (no E mark) Do...
  19. STOKOE

    front bottom arm(rear) bushes ?

    just had my lcr in for a service they guy advised me that both front bottom arm (rear) bushes are starting to seperate and will need replacing anybody any ideas what these are because i haven't a clue.cheers
  20. CupraTgirl

    Split Bottom Hose?

    After what happened with the dent and then having the BIG 60,000 mile Service i thought wicked my car will be fine for a while but i was wrong :cry: I have to say, its nothing that bad but its still frustrating! To cut a long story short, the 'Bottom Hose' has split, meaning the garage...
Chris Knott Insurance - Competitive quotes for forum members