map

Greetings, soon upgrading the Cupra to K04 Hybrid with full fi 76 exhaust R32 style, do I need to remap the car ASAP or I can drive it like this for some time until I fit all the other stuff(rs4 valve,FMIC,HPFP etc...). Will the ECU complain and is there a danger of blowing the piston if the...

Irecently bought a 1.4 DSG 2013 Seat Ibiza Cupra REG is SF13 YWW and I am the 5th Owner it's on 64,000 miles and I would really like to find the owner who done the work to the car because the previous owner owned it for less than a year and claimed the car came with the mods when he bought it...

Hey people please help me. I have a problem with the EGR works when wants to. The EGR is brand new even new pipe to EGR from the throttle body. When I installed the egr come up map problem it rev bouncing in idle. I disconnected the EGR and it settled the problem just at idle revs at 1000rpm...

Hi Guys, As the question asks really, Im desperate for a Stage 1 CC Remap but i dont know if i can get hold of a TIP and get it fitted before the maps done.

Hi Guys, I've recently picked up a Bora 1.8T Sport with full Milltek (downpipe and cat recently replaced under warranty), Carbonio and APR Stage 2 software. It has the AUM engine which as you will know is exactly the same as the AUQ apart from the factory ECU mapping. Same turbo, DBW, VVT...

Does the MAP sensor HAVE to be on the hot side of the intercooler? (or is it on the cold side.. i didn't really check) Having a bit of trouble with a FMIC so i was wondering can i place the MAP wherever i want? Thanks guys

Can someone positively confirm the pressure range of a couple of MAP sensors please?? 038 906 051 C (Bosch ref. 0281 002 401) 038 906 051 D (Bosch ref. 0261 230 073) My information says that the "C" suffix is 300KPa absolute, and "D" suffix is 400KPa absolute (ie up to 2-bar and 3-bar...

The car is as follows : 2004 Cupra (Petrol) Revo Stage 1 Forge TIP Forge 007p (Green spring) Open filter Catback exhaust These are the visual logs I made via the boost gauge tonight (I will get some actual vs requested logs on sunday hopefully) 1.4 bar @ 4k 1.3 bar @ 4.4k 0.9 bar @ 5k 0.8 bar...

On the SMIC, the MAP sensor is at the top near the outlet pipe. Looking to relocate this into a forge map sensor pipe. Do VW/Seat do a blanking plug? IF so, is there a part no.? car is Toledo 1.9TD130

Taught i do some logs since i was out :p Mods Amd stg1 map, fmic, FIP, super sprint full exhaust/decat pipe, ko3s No matter what i do, i wont let me creep past 1bar, as it hits limp mode. :doh: Group A: '003 Group B: '115 RPM Mass Flow Load Ign. Timing RPM Load Absolute Pres...

guys whaddya reckon to having a section where people who have vagcom..vcds, and are prepared to help others with logging, diagnostics etc. could have user, location and ability depending on vagcom license. just notice the requests in vagcom section get answered rarely.... so a vcds...

hello all upgrading to a ko3s soon but cant seem to find any real info on a good place to get a stage 2 map in the south. Im in berkshire and cant find any reviews or feed back from anything local to me. Can anyone help?

Basically im running a mild map (Revo called it that when they checked out my ecu for me) Powerflow cat back FMIC Open jetex filter Forge tip Turbosmart Coldside relocation Usual bypasses Everything was fine but since fitting the coldside it would occasionally cut out when slowing...

Right, checked the pipework for leaks, no luck, everything is tight and secure as it should, used soapy water and no bubbles anywhere. So I'm considering whether it's the MAP sensor? The MAF went a couple weeks back so maybe the MAP has had it's day too? No fault codes on the ECU.

Might be going down to P-Torque soon getting a map and Pipercross induction kit fitted, i have just had a Jetex exhaust system fitted, im gettin a stage 1 map. What gains would i be getting?? Anything else i need to get done whilst im down there to get the best out of the map??

hello i want to know if the dsg box in my fr 170tdi (2010) will be ok to have a remap has i know that over 300ft tuq cluthes start to slip on manual box" how much can one of these boxs handlewith out breaking it

As forge apperantly wont answer me on the forum whether I have to use 60 or 63mm, I have to get an answer elsewhere. So does anyone know which one to use?

i pick up my cupra k1 on friday and it already has a full milteck zorst fitted i wont to remap it wen i get it so wot map do i need is it a stage 2 map also does anyone know the gains with these mods thanks

i have a revo stage 2 on my ibiza cupra, did a log on it last night with vagcom and its running maximum boost, i mean the absolute max the KO3s can do. is this normal for revo to have it set at such an unsafe boost? i didnt get the car mapped but considering ditching the map for a safer one...

Hi, who should I get to map my leon fr tdi CR? Obviosly I don't want to blow my car up with a cheap e bay thing! so if any one has had one of these cars mapped I'd like to know what sort of power and torque they've got and whats the reliabilty and driveabilty like? Thanks in advance Danny