release

Does anyone's boot release button on the key work? Mine hasn't since I got the car. Can it be activated via VCDS?

the leaver does not work and i cannot open the bonnet on my mk2 ibiza any help to open it please as need to get inside urgently

:confused: Need some adivice on this one, I have tried to remove my Aura head unit with the old cut up card technique... no joy. So while I was at SEAT I got one of the guys to put the 2No. removal keys in the slots under the headunit to remove. The problem is the left one clicked and was...

Trying to understand the wiring for the fuel cap release on my 1.9 TDI. It does not show any associated fuses in the owners manual and on the SEAT TIS Service & Repair Workshop Manual CD that I have, it mentions a second fuse/relay panel under the facia - which I don't appear to have?? The...

My 2004 ALTEA 1.9 tdi FR has been absolutely brilliant for 40,000 miles but this week the tailgate release button fails to open the tailgate (I have the central locking, properly unlocked). ie. when I operate the SEAT badge button on the tailgate, it does not pop open. Nothing happens...

Hi all, I am currently trying to put wires through into my doors for my speaker and have done the passenger side no problem but cant get the bonnet release off, any ideas? Many thanks ad

Guys - anyone experienced problem with the boot release for the new Mk5? The Seat badge should spring back but seems to have broken over the weekend - still opens but no spring! Taking it back to dealer & hope it will be covered by the waranty. Hope this is not one of those re-occuring design...

When you press this, is the fuel cap meant to pop out? When i press mine, it seems to just unlock it, and i have to wedge my finger/nail underneath to prise it open????

hi my rear handle sticks open ithink the springs away in it,can these be replaced?thanks

Hi everyone I need to ask if the rear tailgate release handle on my 09 plate 1.4tsi sport has a problem thar is common to the leon's. When you push the top of the seat badge to release the lock it stays in that position. It does not spring back anymore. I'll be taking it back to Seat for...

Afternoon... again my neighbour has asked me (must get him to register himself!!!) about his Mk2 Leon. His manual release on the boot (the seat symbol) doesn't gently sweep back into position (like mine on my Mk1) but you have to push it back in. Anyone else had this? Did it solve with WD...

Hey all. I hope this is the right thread but i got a problem with my Ibiza. I went to open the bonnet and the release cable appeared of of snapped right by the latch. I can see the latch by sticking my head underneath the car but i cant reach it with anything. Tried using wire coat...

Help me PLEEEAAASE! :) Why is there 2 petrol cap switches, and why doesnt one of them work? Only the one near the handbrake works. Also, how do i change the time on the clock? Thanks

Has anyone heard anything about the release of the TDI FR or TDI Cupra (not sure if they are making the diesel Cupra)???

just had to replace my fuel cap and now with the new one on when i press the button inside the car to release the cap it wont pop open. took the whole unit off again and had a mate press the button while i checked the pin. pin seems to go in and out freely when the button is pressed so obv in...

My door release broke, so when i tookt eh door apart i found this: The other end of the cable connects to the lock unit as below, Can i just buy the cable and fit it in? or do i need a whole new lock unit for the inside of the door? And how tricky is this to do if its even...

Hi guys. I've recently fixed my smoothed boot release. I decided to wire it onto the fuel cap release feed. Worked perfect. However yesterday i put two tyres in the boot which i didnt release had compressed on the glass which would apply pressure onto the lock, went to open the boot and it...

Noticed a bit of a groaning noise (yes, I am completely aware of the comments that will follow:censored:) last night when the car was idling, press in the clutch noise goes. They reckon release bearing is gone in the clutch. Bottom line is a new clutch (could just do the bearing but while...

im looking to make an alloy cover for the seat release catch on the cupra to add a bit of alloy to the cabin, i wondered if anyone could help me by making a mould of the origional somehow, or tell me how to do so, ive not a clue what to use to make the copy of it, and any other ideas for parts...

More in-depth info released today by SEAT. http://www.seatcupra.net/index.php?option=com_content&task=view&id=1057&Itemid=1 plus a shed load of new images. http://www.seatcupra.net/gallery/main.php?g2_itemId=32007