Shells ShAlhambra
- Thread starter MarkWales
- Start date
nothing would shift the nut!
in the end we disk cut as much as we could until we could get the cap through the inner wing.
in the end we disk cut as much as we could until we could get the cap through the inner wing.
update for today replaced both bottom ball joints today due to excess play in them
thinking of rebadging it with
T A R D I S
using the original letters
thinking of rebadging it with
T A R D I S
using the original letters
Just picked up
from a Passat
going to fit in the morning.
And the Shalhambra is now wired to tow
from a Passat
going to fit in the morning.
And the Shalhambra is now wired to tow
Todays Mod
from the earlier Model means all occupants can see the time not just the driver - Hopefully save the kids asking the time!
from the earlier Model means all occupants can see the time not just the driver - Hopefully save the kids asking the time!
came today
I have allready installed this kit on the LEON and work great cannot fault the value at less than £15 delivered - also was only ordered on saturday
I have allready installed this kit on the LEON and work great cannot fault the value at less than £15 delivered - also was only ordered on saturday
mmmmm problem time may be caused by me lol
drained the coolant bottle to refil with antifreeze yesterday morning ran for a while to check for trapped air all OK
Driving home from Cardiff last night car Overheats and blew out a load of coolant when I opened what looked to be an empty coolant bottle - left the lid off today and ran for ages to get the internal blowers warm - not a happy bunny!!
Still must have air in the system as the rear heaters are not getting warm will try and re bleed tomorrow.
Anynone know if there is a bleed valve or similar on the PD engine?
drained the coolant bottle to refil with antifreeze yesterday morning ran for a while to check for trapped air all OK
Driving home from Cardiff last night car Overheats and blew out a load of coolant when I opened what looked to be an empty coolant bottle - left the lid off today and ran for ages to get the internal blowers warm - not a happy bunny!!
Still must have air in the system as the rear heaters are not getting warm will try and re bleed tomorrow.
Anynone know if there is a bleed valve or similar on the PD engine?
Do you not need to massage the pipes to flush it round?
Be interested in your parking sensor install too
Be interested in your parking sensor install too
have installed them on the Leon already - need to look into a front set for the sharan and maybe the oem switch for them
Last edited:
More bad news coolant issue seems more than just an air lock now looking at
http://www.fgoc.co.uk/forum/index.php/topic,7838.msg70196.html#msg70196
maybe water pump or head gasket
http://www.fgoc.co.uk/forum/index.php/topic,7838.msg70196.html#msg70196
maybe water pump or head gasket
So some cosmetic mods which are a little marmite
mainly down to the rubber handles and trim wearing
from
to
and then the dash strip to match
cut to size
wrapped
fitted
and the passenger side wrapped
and fitted
to do the next console then the top box door mouldings and remaining handles
mainly down to the rubber handles and trim wearing
from
to
and then the dash strip to match
cut to size
wrapped
fitted
and the passenger side wrapped
and fitted
to do the next console then the top box door mouldings and remaining handles
Last edited:
I'm not totally offended by that vinyl wrap on the interior.
CV boot is easy enough to do, should take a half competent garage only an hour to do
CV boot is easy enough to do, should take a half competent garage only an hour to do
Well Replacement Drivefshaft fitted - Piece of P*ss to fit took 1 1/2 hours with no great rush. MOT in the morning. We shall see how the old girl gets on.
After MOT with all being well next weekend the rear reverse sensors are going in.
Possibly a mufflerectomy and induction cone to try and get her reving a little more freely.
After MOT with all being well next weekend the rear reverse sensors are going in.
Possibly a mufflerectomy and induction cone to try and get her reving a little more freely.
MOT Passed - Advisory on blowing exhaust - MOT inspector told me sounds like time you had a stainless decat system like the Leon has lol.
Quick Recent Picture on Alloys and steels on front for winter tyres
Quick Recent Picture on Alloys and steels on front for winter tyres
Last edited:
