Dismiss Notice
Hi Guest, stickers are available from our online store.

Wash level indicator in winter pack

Discussion in 'Ateca' started by dajoco, Dec 16, 2017.

  1. dajoco

    dajoco Active Member

    Joined:
    Dec 16, 2017
    Messages:
    2
    Likes Received:
    0
    I am enjoying our new Ateca 1.4 SE which we have now been running for about 6 weeks. We opted for the winter pack and the heated front seats have been appreciated in this cold snap. However, one of the features of the Winter Pack should be a wash water level indicator. I can see no sign of it and the manual does not seem to mention it (although the indexing in the manual leaves much to be desired). Please could anybody tell me where the wash level indicator is situated?
     
  2. Tell

    Tell Full Member

    Joined:
    Jun 27, 2004
    Messages:
    2,539
    Likes Received:
    296
    I can't say that I have seen the indicator but then I have never emptied the reserve, I do have the winter pack. The latest Ateca manual ATECA User Manual_11_17_EN.pdf page 48 shows the warning light

    Level of windscreen washer
    fluid too low.
    ››› page
    153


    Then seems to fizzle out about talking about the subject.

    It might be lurking in the ErWin materiel or one of those features that's in the manual but not on the car. You would expect a sensor on the reservoir bottle. That you might find in the ErWin manuals although wasn't mentioned in the maintenance manual apart from top up.

    Yes page 57 / 58 Ateca 2017 ➤
    Electrical system - Edition 07.2016

    The Erwin manuals you pay your money and download. Good resource. I gave a link on here.
     
  3. dajoco

    dajoco Active Member

    Joined:
    Dec 16, 2017
    Messages:
    2
    Likes Received:
    0
    Thank you. That was helpful.
     
  4. Tell

    Tell Full Member

    Joined:
    Jun 27, 2004
    Messages:
    2,539
    Likes Received:
    296
    I was on a ferry and was going to edit the link into the ErWin materiel

    http://www.seatcupra.net/forums/showthread.php?t=438077

    Text and there is a picture... text

    2.3 Removing and installing windscreen
    washer fluid level sender
    Special tools and workshop equipment required
    ♦ Drip tray - VAS 6208-
    Ateca 2017 ➤
    Electrical system - Edition 07.2016

    ♦ Lever - 3409-
    Removing
    – Turn off the ignition and all electricity consumers.
    Vehicles without access and start authorisation system
    – Remove ignition key, if fitted.
    Vehicles with access and start authorisation system
    – Store the ignition key outside the vehicle to prevent the ignition
    from being switched on unintentionally.
    Continuation for all vehicles
    – Place the vehicle on a lifting platform.
    – Remove the left front wheel ⇒ Rep. gr. 44 ; Rims and Tyres .
    – Remove the spoiler on the front left wheel well ⇒ Chassis -
    external assembly work; Rep. gr. 66 ; Wheel well liner .
    – Place the drip tray for fluids - VAS 6208- under the washer fluid
    reservoir.
    – Removing the front bumper lining ⇒ General body repairs,
    exterior; Rep. gr. 63 ; Front bumper; removing and installing
    the front bumper lining .
    – Disconnect the electrical connector-2- from the sender for
    washer fluid level -3-.
    – Pull out sender for filling level-3- using the lever - 3409- from
    the washer fluid reservoir -1-.
    Installation
    Installation is carried out in the reverse sequence; note the fol‐
    lowing:
    – Check the sealing lip between the sender for filling level -3-
    and the washer fluid reservoir -1- for damages.
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice